Pronghorn MFES-JK C2-S Front Bumper for Jeep Wrangler JK (MFES-JK-C250)


Outfitting your vehicle for off-road and expedition work comes down to selecting the right gear for the specific terrain and task at hand. When we designed the MFES-JK we weren’t just redesigning the traditional front-end system, but also redesigning how people are better able to use their off-road gear. In addition to lightweight and high-strength performance we have added a new level of functionality to off-road equipment in the form of numerous accessories and tools that change the standard front bumper into a full function accessory mounting system for the Jeep JK.

$0.00

Pronghorn MFES-JK-C25O Front Bumper   +$1,790.00

Pronghorn MFES-JK C2-S Front Bumper for Jeep Wrangler JK

Double click on above image to view full picture

Zoom Out
Zoom In
  • Pronghorn MFES-JK C2-S Front Bumper for Jeep Wrangler JK
  • Pronghorn MFES-JK C2-S Front Bumper for Jeep Wrangler JK
  • Pronghorn MFES-JK C2-S Front Bumper for Jeep Wrangler JK
High-Strength Meets Lightweight
Traditional off-road gear is strong, but it is also seriously heavy. This extra weight overloads the vehicle suspension and adversely effects vehicle performance, handling, and endurance. Our US-made Modular Front-End System (MFES) is built with a fully boxed design for strength and laser cut, Tig welded aluminum for light weight. All the strength of a comparable steel bumper system, at half the weight, for maximum performance. 

Full Modular Design
Not every off-road vehicle is going to need the same front-end system. You may require full grill and headlight protection. Or perhaps you need maximum approach angles and clearance for technical trails. We designed the MFES to be fully modular with 18 configurations that allow you to design the front-end system that best fits your specific requirements. Bolt on the stub outers for maximum approach angles or full width outers maximum protection. Select the clean and simple performance of the C1 or C1-S or the full grill and headlight guard protection of the C9 and C9-S. Design the system you need and have the freedom to upgrade and modify as your off-road and expedition requirements change.

Advanced Recovery Gear Options
This is off-road and that means you will need recovery gear. For the MFES we provide multiple recovery gear options, as well as multiple mounting points to meet your specific recovery requirements. From dual recovery hooks, to the high-strength shackle mounts (left and right side mounting options), to our patented maximum strength. Rotator Shackle Mount, we offer the largest number of recovery options of any front-end system to meet your needs. Need a winch? We offer a traditional top mount winch option in addition to our innovative GearMount winch system. allowing you to quickly and easily attach the winch when and where you need it.

GearMount™ Accessory System
Well designed off-road and expedition gear should include some serious functionality. So, in addition to providing numerous pre-drilled mounting points for your accessories, we added our patented GearMount accessory mounting system. GearMount allows you to quickly and securely attach winches, cargo racks, work/cook tables or any of the other GearMount accessories to the MFES, our rear bumper system and our side rail system. And unlike loose fitting receiver hitch mount designs the GearMount system uses two dedicated mounting points that provide secure, zero-freeplay gear attachment. Can install it with basic hand tools. No die grinders, cut-off wheels, or paint required.

Convenient UPS Shipping – No Freight Required
Our lightweight, modular design not only gives you great performance and modular design, it also saves you money and hassles with shipping. Due to their size and weight, most comparable fixed-design bumper systems must be shipped via expensive freight carriers ($175-250 on average). That means more money out of your off-road budget, plus the hassles of no home delivery. Our MFES ships via UPS Ground, typically 30-40% the cost of freight, and it comes directly to your front door.

DESIGN / PERFORMANCE
  • Full Modular Design with 18 Configurations
  • Lightweight / High-Strength Aluminum Design
  • Fully Boxed Design for Maximum Strength
  • 2 and 3-Stage Powder Coating
  • Triple Coated Grade 8.8 Fasteners
  • US-Made

RECOVERY / PROTECTION

  • Optional Dual Plate Aluminum Skid Plate
  • Advanced Multiple Recovery Gear Options
  • Optional Gearmount Winch System
  • Optional Top Mount Winch
  • Optional HiLift Jack Shackle System
  • Integral Jack Points

ACCESSORIES

  • Pre-Drilled Auxiliary Light Mounts (9 Locations)
  • Factory Driving Light Mounts
  • Multiple Cargo Tie-Down Points
  • Optional Traction Cleats
  • Optional Splash Guards

INSTALLATION AND SHIPPING

  • No Cut / No Drill Installation
  • UPS / FedEx Shipping – No Freight Required
Lightweight Strength Matters
Off-road and expedition gear needs to do two primary things: 1) Protect the vehicle from a reasonable level of possible damage, and 2) not restrict or inhibit the performance of the vehicle. Most companies building off-road gear do very well in building for Item 1, but they seem to neglect Item 2. This has resulted in some extremely strong, but extremely heavy vehicle protection equipment and heavy does not mix well with vehicle performance or cargo capacity.

The additional weight of a heavy steel front bumper translates directly into a reduction in vehicle performance (off-road capabilities on soft surfaces, acceleration, braking, and handling). In addition, the increase in weight of the front (and rear) bumper components directly effects the cargo weight capacity of the vehicle. The heavier the bumper, the less gear you can carry based on your suspension set-up. And these performance and cargo reductions also mean a reduction in vehicle range, due to both reduced fuel economy and reduced extra fuel capacity (lower available cargo weight).

Fully Boxed Strength
A well designed off-road front-end system needs to be strong enough to absorb and deflect impacts. The Pronghorn MFES is engineered with a fully boxed design to shrug off off-road impacts. This design is considerably stronger than the open or U-section design used by nearly every other manufacturer. Our fully boxed design is more expensive to produce, but it gives us a stronger and lighter part.

This fully boxed structure is also design to provide controlled deformation in a vehicle-to-vehicle collision. This “as strong as it needs to be” approach allows the MFES to shrug off impacts found in off-road environments, while still providing the right amount of deformation during collisions to protect the vehicle frame and crumple zones, as well as the vehicle occupants. A bumper is of little value if your bumper survives the collision, but your frame is damaged and your Jeep is totaled.

Aluminum, Corrosion and Coatings
When designing the Pronghorn MFES, as well as our upcoming Modular Rear Bumper System (MRBS), we knew we needed to reduce weight while still providing strength. High-strength aluminum was the logical choice. Ask an engineer, or anyone in motorsports or aerospace, and they will tell you the benefits of aluminum: Lightweight, excellent strength-to-weight ratio, and minimal maintenance (rust proof).

We engineered every aspect of the MFES to contend with the abuses of the off-road environment while still delivering lightweight performance. The main and outer body sections of the MFES are constructed from 3/16” 6061-T6, marine-grade aluminum to provide optimal strength and impact resistance. Recovery gear and mounting points are CNC machined from 6061-T6 and 7075-T6 aerospace-grade aluminum for extra strength.

One of the key advantages of aluminum in the off-road environment is that, unlike steel, is does not rust. This can be a big advantage if you are in environments with salt exposure (salted roads, coastal regions) that can take a heavy toll on steel components. Though that doesn’t mean we don’t take our coatings seriously. All components receive a 2-stage Dupont powder coating process. The center and outer body sections also receive an alodine dip to fully coat the interior of the components.

To ensure high-strength performance we use all grade 8.8 fasteners on the MFES treated with a 3-stage OE-grade coating for maximum corrosion protection (1,000+ hr salt spray test certification).

Whether the aluminum structure, the coatings or the fasteners. Every aspect of the MFES has been designed to deliver lightweight and high-strength performance in every off-road and expedition scenario.

Materials
  • MFES Center and Outer Body Sections
  • 3/16” 6061-T6 Aluminum
  • Laser Cut
  • CNC Bent
  • Tig Welded
 

Upper Sections

  • 1/4” 6061-T6 Aluminum
  • Laser Cut

Recovery Gear and Mounting Points

  • 6061-T6 and 7075-T6 Aluminum
  • CNC Machined

Powder Coating and Protection

  • 2-Stage Powder Coating (Dupont)

MFES Body and Outers

  • Alodine Dipped / 2-Stage Powder Coating (Dupont)

Fasteners

  • Grade 8.8
  • 3-Stage OE-Grade Coating – Maximum Corrosion Resistance (1000+ hr salt spray test)

Vehicle Make

Jeep

Vehicle Model

Wrangler JK

Vehicle Year

2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015

Special Fitment Notes

No

Manufacture Part Number

MFES-JK-C250

Part Number

N/A

Free Shipping

No

Manufacturer

Pronghorn

Installation Difficulty

No

Installation Instructions

Not Available

There are no reviews yet.
Be the first one who writes a review.

Post a New Review

You're reviewing: Pronghorn MFES-JK C2-S Front Bumper for Jeep Wrangler JK (MFES-JK-C250)

Only registered users can write reviews. Please, log in or register

Compare Products

You have no items to compare.