EvoBaskets

Evobaskets was founded to provide the highest quality cargo basket on the market, with enough adjustability built-in to fit most vehicles. Our basket is also modular to accommodate a full line of accessories. Whether you are a surf fisherman looking to add rod holders, a car camper looking for extra storage, or a vacationing family in need of a beach cart, we have you covered.

$380.00

1

EvoBaskets

Double click on above image to view full picture

Zoom Out
Zoom In

Evobaskets was founded to provide the highest quality cargo basket on the market, with enough adjustability built-in to fit most vehicles. Our basket is also modular to accommodate a full line of accessories. Whether you are a surf fisherman looking to add rod holders, a car camper looking for extra storage, or a vacationing family in need of a beach cart, we have you covered.

Basket Base (Included in Price)

The base of the Evobaskets system is our basket.  Designed to be the strongest, longest lasting cargo carrying basket on the market, Evobaskets went back to the drawing board when designing the flagship of our line.  We wanted the basket to be height adjustable (we have over 12” of height adjustment with our base hitch included when purchasing the basket) and wanted to use components that would last.  The main basket is 100% aluminum, so no rusting with our product.  With usable inside dimensions of 45” wide by 19” deep you can fit the largest of coolers (up to the Coleman 150qt) in this basket.

Our main “L Plate” is router cut for precise fit out of 3/16” 6061 aluminum and designed to transfer the load not to welds but direct to our hitch assembly eliminating a common failure point in other designs.  All the tubing for sides and floor is 1/8” wall tubing which will hold up to excessive abuse long term.  Additionally we have Evobaskets unique side accessory plates included on all baskets.  You get 6 different accessory mount locations on every basket where you can add any of our accessories you desire, making your basket your own.

Our hitch is the only steel part in our line, and that was done to maximize strength.  Yes rust could set in, however by the time that happens an aluminum counterpart would most certainly have failed.  With our unique hitch design you not only get 12” of vertical height adjustment but you also get 4 hitch pin locations allowing you to slide your basket closer to the rear bumper or further away to clear opening rear lift gates or tailgate mounted spare tires.
All our baskets and hitch assemblies come powder coated, the basket silver and the hitch black.  

Our baskets come standard with stainless bolts for assembly to the included hitch, you simply need two ¾” wrenches for assembly.  We also offer a pin kit which will include two pins to replace the bolts.  This would allow quick removal of the hitch assembly for easier storage or use of our cart add on accessory.

Basket Options

Tapered 3-Rod Holder
Our Tapered 3 Rod Holder is just that, we taper from a tall rod holder (28”) to a medium length holder (24”) to a shorter rod holder (20”).  These holders are sold in pairs so you get a left and a right, however you have the option to mount these holders in any one of the 6 locations on our basket or two locations on our Evo-plate.  What this means to you is you set the basket up how you want it, do you want the tall holder in the middle, great, want the tall holder on the outside simply flip the holders from right to left.  Is mounting to the side more your speed, great, you have options.  Included with our Tapered 3 Rod Holders will be 6 rod keepers from Surfcaster.  In researching tops for our rod holders we found Surfcaster to have the highest end top available and was an easy decision to include these in our line.  Additionally we will include all stainless hardware for mounting to our basket, you simply need two ½” wrenches for assembly.  Already have an accessory where you want your rod holder?  No problem, simply add one of our spacer kits and “stack” two accessories in one location (not all accessories can be stacked, consult an Evobaskets representative before purchasing).



Level 3-Rod Holder
Need more rod storage, or prefer your reels all being level, then our Level 3 Rod Holders are your answer.  These holders have rod tubes all 20” in length (designed to match the height of the shorter tube in our Tapered 3 Rod Holder), come in a pair of rod holders (so you can hold a total of 6 rods), and can mount in any of our mounting locations.  Included with our Tapered 3 Rod Holders will be 6 rod keepers from Surfcaster.  In researching tops for our rod holders we found Surfcaster to have the highest end top available and was an easy decision to include these in our line.  Additionally we will include all stainless hardware for mounting to our basket, you simply need two ½” wrenches for assembly.  Already have an accessory where you want your rod holder?  No problem, simply add one of our spacer kits and “stack” two accessories in one location (not all accessories can be stacked, consult an Evobaskets representative before purchasing).




Angled Rod Holder (Short)
Our Angled Rod Holders are offered in short and long configurations.  The short is designed for “rigging” or “baiting” your rods and traditionally mounted to the outside accessory locations on our basket.  The long is designed to be an opposite facing rod holder for the extra-long heaver type rods to help with overhead clearances on the roads.  By angling a rod backwards over the hood and roof of the vehicle you are gaining over a foot of overhead clearance.  So now you can travel around Ocracoke Island and hit fewer trees!  The angled short has a tube length of 15” while the long extends that tube length to 28” to protect your rod.  The Angled Short comes with a pair of holders, standard rubber top grommet, and of course stainless hardware to install.  The Angled Long comes with a pair of holders and standard with Surfcaster toppers and stainless mounting hardware.  Two ½” wrenches required for installation.  Already have an accessory where you want your rod holder?  No problem, simply add one of our spacer kits and “stack” two accessories in one location (not all accessories can be stacked, consult an Evobaskets representative before purchasing).

 

 


Angled Rod Holder (Long)
Our Angled Rod Holders are offered in short and long configurations.  The short is designed for “rigging” or “baiting” your rods and traditionally mounted to the outside accessory locations on our basket.  The long is designed to be an opposite facing rod holder for the extra-long heaver type rods to help with overhead clearances on the roads.  By angling a rod backwards over the hood and roof of the vehicle you are gaining over a foot of overhead clearance.  So now you can travel around Ocracoke Island and hit fewer trees!  The angled short has a tube length of 15” while the long extends that tube length to 28” to protect your rod.  The Angled Short comes with a pair of holders, standard rubber top grommet, and of course stainless hardware to install.  The Angled Long comes with a pair of holders and standard with Surfcaster toppers and stainless mounting hardware.  Two ½” wrenches required for installation.  Already have an accessory where you want your rod holder?  No problem, simply add one of our spacer kits and “stack” two accessories in one location (not all accessories can be stacked, consult an Evobaskets representative before purchasing).



Utility Platform / Bait Bucket Holder
Because many anglers have a need/desire to carry items in addition to their main cooler we designed the Evobaskets Utility Platform (EUP).  With a base area of 12” wide by 12” deep you have the option of using it to carry a 5 gallon bucket, bait cooler, tackle box, etc., the option is yours.  Router cut from 1/8” aluminum then press bent and welded this platform is designed to last.  The EUP has our EVO logo cut in the front and back which also doubles as a location to attach “bungee cords” for securing whatever item you wish to carry.  As with all Evobaskets products we include the necessary stainless steel hardware to attach to any one of the mounting locations (requires two ½” wrenches to install).   Already have an accessory where you want your rod holder?  No problem, simply add one of our spacer kits and “stack” two accessories in one location (not all accessories can be stacked, consult an Evobaskets representative before purchasing).


 

Cooler Hold Down w/ Cutting Board
Tired of using cords or straps to hold your cooler lid from opening while driving down the road?  Tired of the grime from cut bait staining your cooler lid?  Then the Evobaskets Cooler Hold Down (ECHD) is your solution.  Designed to double as a cutting board as well, the hold down has an adjustable clamp so you can adjust the height for many coolers, and when you get to your fishing location simply loosen the clamp, spin the cutting board forward, and now you have access to your cooler with a cutting board in front as well.  The ECHD also includes locations for mounting license plates to the front of the basket, or keep it blank, the choice is yours.  (Warning, the user is responsible for final adjustment of the clamp to ensure cooler lid will not open at speeds).

Manufacture Part Number

EvoBaskets

Part Number

N/A

Free Shipping

Yes

Manufacturer

EvoBaskets

There are no reviews yet.
Be the first one who writes a review.

Post a New Review

You're reviewing: EvoBaskets

Only registered users can write reviews. Please, log in or register

Compare Products

You have no items to compare.